Discovering Plumbing Basics is Vital for Bathtub Installation
Discovering Plumbing Basics is Vital for Bathtub Installation
Blog Article
Just how do you feel in regards to How to Install a Bathtub?
Installing a bathtub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately hard job. If the old tub is conveniently easily accessible, the task can relocate easily; if you need to open up a wall to remove the old tub and position the new tub, the job is a lot harder. In either case, the task is within a house handyman's abilities, although you will certainly require an assistant to leave the old bathtub and embeded in the new one. Ensure you have qualified on your own for the work and are comfortable attempting it. Instead of working with a professional to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Possibilities are you might need an expert plumber to make tube connections.
This short article will help you set up a new bathtub in your restroom if you have currently gotten a new tub and also do not require to alter the setup of your previous supply of water pipes.
Your devices and also product list should consist of the following:
Getting ready for the Installment
Firstly, the supporting framework provided with the bath needs to be fitted (if needed) according to the producer's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to ensure that if the faucet features a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must now prepare to be fitted in its final placement.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The process of removing the existing taps can be quite problematic because of the restricted access that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a towel prepared for the remaining water that will originate from the pipelines. Once the supply pipelines have been removed, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this process. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing substance.
Before going on to fit the new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Bath tub
Using the two wooden boards under its feet, place the bathtub in the needed setting. The wood boards are useful in uniformly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four tiny points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub until the level checks out degree.
To set up taps, fit all-time low of the furthest adaptable faucet adapter to the suitable supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water system as well as examine all joints and brand-new pipework for leaks and tighten them if necessary. Fill the tub and also examine the overflow outlet as well as the normal electrical outlet for leakages.
Finally, deal with the bath paneling as defined in the producer's user's manual. Tiling as well as securing around the bath tub should wait until the tub has actually been made use of at least when as this will certainly settle it into its final position.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin guaranteeing that the washing machines are in place in between the faucet and the sink. Secure the faucet in place with the producer provided backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The former kind should be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bath satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture an inflexible seal, causing the water to penetrate the wall surface in between the bathroom and also the tiling, leading to complications with dampness as well as possible leaks to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your components as well as fittings. They are sold in tubes and also cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of drenched paper or soft rope. Remember to constantly load the tub with water before securing, to enable the activity experienced when the bathtub is in usage. The sealant can crack rather very early if you do not consider this activity before securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading about Installing A Bathtub? Make a comment directly below. We would be glad to know your opinion about this blog post. We are looking forward to see you back again later on. Those who enjoyed our blog entry please don't forget to pass it around. Thanks a lot for your time. Visit us again soon.
Get An Estimate Report this page